How to use a hammer drill – A Step by Step Guide

If you want to put up shelves, hang paintings, install lights then you need the best hammer drill. It is the best tool to perform your selected job especially when you want to make holes into the wall or on a solid surface.

The hammer drill has pushed and pulls motion comes with drilling effect are considered the main features of the drill. It can perform its drill work even on tough materials more quickly than others.

In my article, I will show step by step guidelines so that if you read this instruction you able to gain appropriate knowledge about assembling, operating and maintaining your drill.

This article has been designed for the hammer drill and contains all important information to make sure your correct and safe use.

If you follow my instructions it will ensure you and your product highest safe that confirms a longer life of your product.

If you spend just a few minutes from your most valuable time also you can discover in the best way of how to use a hammer drill. No matter if you are at a beginner’s level my article would be a proper guideline for you.

So, why waiting starts reading!!

The hammer drill is basically used for making holes in concrete especially wall or concrete floors. Also, you can use for inserting and removing screws.

It is really handy techniques if you able to make holes in concrete. This process generally simple but you need to select the right tools and want to gain knowledge of how to use them in a proper way to save your lot of time.

In the article, I categorized 3 key stages to explain you of using your hammer tool more efficiently. And these main stages and other striking features are discussing below:

Basic preparation of using your product:

Select your hammer drill:

If you are planning to buy for your home purpose then you do not need to buy an expensive hammer drill. An inexpensive drill is 21adequate to complete your drill projects.

However, if your intention is to invest your money for commercial work then you have to buy an industrial-quality hammer drill. The commercial hammer drill will solve your heavy duty drill work but it is expensive compared to home use drill.

Know your drill bits:

You should have a proper idea about which drill bits use for what materials. Because, one bit does not suitable for every task.

If you need to use your bits for woodworking then you want pointed tips and ones that have solid back are normally used for metals. Screw bits and hexagonal slots are used for other screw heads.

Get an idea about user manual:

You have a plan to read the user manual every time because it helps you to cope yourself with the drill. You need to follow all safety procedures included in the manual.

General safety procedures:

You need to read owner’s manual that comes along with your hammer drill box. If you do not follow the instructions you may face severe injury or even damage your tool.

[su_list icon=”icon: arrow-right” icon_color=”#329d40″]

• Maintain a tidy and clear area for you drill work.
• Do not get closer with liquid, gasses and other inflammable.
• Do not abuse your drill power tool cord
• If you work in a damp location always use a GFCI supply to reduce the risk of shock.
• Keep proper distance and sense of balance all time
• Do not create extra pressure on the power
• Do not use the tool if switch ON/OF button does not work properly.
• Always wear ear protection with an impact drill.
• Always wear eye protection for extra safety
• Use extra handles supplied with the drill
• Use a mask when you work in the dust area.

[/su_list]

Unpacking and checking:

You need to take out your hammer drill to check if is there any sign of damaged then contact immediately with the manufacturer or suppliers.

Get ready for hammer drill:

If you control the hammer drill loosely then it may cause personal injury. It is advisable to use extra handles that supply with your tool.

You need to:

[su_list icon=”icon: arrow-right” icon_color=”#329d40″]

• Make sure the hand grip not tight
• Select an angle according to your requirement to get a secure handgrip.

[/su_list]

Basic Operational instructions:

If you want to activate your hammer drill just press the trigger for few moments. Also, you need to hold and trigger the button when you are planning to operate your drill bit longer. Hammer drill always follow built in reverse speed that helps you to remove jammed drill bits.

Start your drill work:

When you get ready then start drilling. If you start your project it will make you expert after practicing a reasonable amount of time.

Wood, Composite, and plastic:

You need to select your drill operating mood and start drilling with low speed that ensures the bit not slipping off the starting point. Increase a reasonable amount of speed when you find out the drill bits into the material.

If you make holes you have to put a piece of wood just another side of the material to avert your tattered and fractured restricts back side.

Metal or steel drilling:

When you work on metal or steel you need to put some oil or another kind of liquids on the quick speed steel bit that will minimize the overheating.

If you put some liquid on the bits it will last long and give you standard drilling action.

You have to be very careful of your drilling work. You do not bend or burn out bits otherwise it produce off-centre or irregular shaped holes.

Also, for making larger holes in metal my advice first start with a small bit then move forward to use a larger bit for your final finish. You must use a coolant for drilling copper, brass or aluminum.

Brick, Tile, Concrete etc:

If you are looking for most performance outcome from your drilling work, then make sure you want carbide-tipped masonry impact bits. Also, you need to adjust your speed to medium level in bricks to get best results.

If you plan to drill in concrete or other tough materials then put additional pressure. The more you involve in-depth drilling the more pressure you need to apply.

Moreover, for drilling work in tile, do some practice on a scrap piece to decide the top speed and pressure in according to tiles condition.

First, start drilling at a very low speed to avoid the slipping off from starting point otherwise you will get worst results that may cause breakdown or need to replace your expensive tile.

When you get a smooth and small flow of dust it is the confirmation that you are using the proper drilling rate.

You do not allow the bit spin in the hole unless cutting and never try your drill work in steel reinforcing rods. Both your actions will cause severe damage the carbide.

These are the few possible drill work and how you perform your drilling. My honest advice to before you start your drill work do lots of demo and practice get all the information into your mind then go for practical drilling.

At the beginning of your work, your hands may shake and not perfect to the right holes but keep trying, don’t lose your dedication, and focus work only then you will be an expert in using a hammer drill.

Basic FAQ for your better understanding:

How can I take away dust from a bottomless hole?

You need to use your shop vacuum but do not just place it in the hole. Use your hand in the last end of your vacuum and allow some air come through your fingers. This process will suck up all the dust and clean the hole.

I do not have a hammer drill but I really need one, what can I do?

Wide ranges of hammer drill are available in the market within your price range. If you do not have one either you can buy or just rent one.

Are there any guidelines to follow, to confirm there are no wires in the wall?

There is no hard and fast rule so you can avoid wires in the wall but be sure all lights are switched on in the room use your basic knowledge before using a wire finder.

Can you tell me the depth level when I drill into concrete?

Select screw size at least 1 inch and add 1 inch to the thickness of the material, but for maximum strength use longer screw up to 1-3/4 inch.

What would be the holes distance while drilling into concrete?

Holes to drill in concrete should be at least ¼ inch. A little extra space helps you to remove dust but you must go for adjustable depth end.

Are there any anchors needed in the present slab during an apron pouring?

You need an impact drill and drill 6”(1/2”) Dia into existing slab at 18” o/c. Seal the hole with epoxy and then insert 3/8” Dia rebar that is 12” long into the hole. It enables to 6” and then it allows you pour your new slab.

Are there any preconditions for a successful masonry nail drive into concrete?

You have to follow 4 tips and these are:

1. The right nails
2. The appropriate hammer
3. Powered nail gun
4. Shanks

Final Verdict:

It is advisable you follow the above procedures of how to use a hammer drill. Failure to maintain a balance between your work and equipment could cause severe damage to your hammer drill and unavoidable personal injury.